Design For TOYOTA TUNDRA Ivan Stewart TRD 2010 2014 2015 2016 2019 2020 2021

Design For TOYOTA TUNDRA Ivan Stewart TRD 2010 2014 2015 2016 2019 2020 2021
Design For TOYOTA TUNDRA Ivan Stewart TRD 2010 2014 2015 2016 2019 2020 2021
Design For TOYOTA TUNDRA Ivan Stewart TRD 2010 2014 2015 2016 2019 2020 2021
Design For TOYOTA TUNDRA Ivan Stewart TRD 2010 2014 2015 2016 2019 2020 2021

Design For TOYOTA TUNDRA Ivan Stewart TRD 2010 2014 2015 2016 2019 2020 2021
TRD 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015. 2016 2017 2018 2019 2020 2021. The Kit include both sides. Default color as 1st Picture. High grade Vinyl as Factory Spec (Polymeric). Available Colors are: Matte Black – Gloss black – White matte – White gloss – Gold – Silver – Black – Grey – Yellow – Forest Green – Red – Blue – light Blue – Orange – lime green. Clean the vehicle surface thoroughly. Pay special attention to edges, and cracks that may be hiding dust or grime. Test fit by holding your vinyl in place with masking tape. Mark position with tape, or tape in place along top edge, allowing you to peel the backing paper. Make sure the decal is not backwards. Right side decals will only fit well on the right side of the car and vice-versa for the left side. Wet vehicle surface with water solution (See general instructions above). Try to avoid getting the backing paper wet. It would cause it to break down and make it harder to remove. Peel backing paper and generously spray adhesive side of vinyl with water solution. Make sure positioning is correct. (Water allows you to temporarily slide the vinyl around the surface). Once you’re happy with the position, move to the next step. Step 6: If working with solid stripes, or unmasked vinyl, spray top of vinyl before you squeegee to avoid scratches. If in doubt, spray more. It’s good to work with lots of solution, even on your hands. Firmly squeegee vinyl in place, working from center out. If the vinyl moves at all while trying to squeegee, spray more solution and carefully reposition. Be careful not to stretch the vinyl too much as it might deform. Spray masking / transfer tape to loosen and let sit for 5 minutes. This allows it to loosen enough and also give the vinyl time to stick better to the car’s surface. Carefully peel back masking / transfer tape, keeping it flat with the surface so you don’t peel up the fresh vinyl. If some of the vinyl peels off you can add solution and slip back into place and squeegee again. Trim extra overlap along edges with razor blade if needed. In more cases you won’t need to trim, though some kits require it. Just be careful not to scratch the paint when trimming. Most bubbles will squeegee out. However, some remaining bubbles can be carefully popped with a needle or corner of your razor blade before pressing down on it again. Park in the sun to help the stripes dry quicker. The hot sun will also help get rid of some bubbles. Allow a few days with the car in a sun before attempting to wash the vehicle. During this time, be gentle when you wipe down the car or the graphics to avoid damaging them. After a few days you can begin to handle the car as you normally would. If item arrive damaged we are happy to send a free replacement Please send a message before open case, we are happy to resolving issues with customers. Response within 24 hours. We are happy to help solving any issue. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts & Accessories\Exterior Parts & Accessories\Decals & Vinyls”. The seller is “ultimate_pro_designs” and is located in this country: CY. This item can be shipped worldwide.
  • Suitable For: Car
  • Country/Region of Manufacture: Cyprus
  • Material: Vinyl
  • Universal Fitment: Yes
  • Finish: Glossy
  • Manufacturer Part Number: Code-trd
  • Brand: ultimateprocy1
  • Color: RED-ORANGE-YELLOW
  • Theme: Graphic
  • Type: Decal

Design For TOYOTA TUNDRA Ivan Stewart TRD 2010 2014 2015 2016 2019 2020 2021